LDG & Misc. Cables Cables for Interfacing LDG Autotuners & Radios

IC-1  IC-2 Y-ACC Push-to-Tune Aux. Power Cable In-Line Fuse Cable LDG Power Cable FT-817 Power Cable AT-897 CAT Cable NO PHOTO Cable for AT-7000 Connecting to IC-7000 DIN-8 Pigtails IC-7K Cable N/A ************************************************************************************* SEE DESCRIPTION OF CABLES BELOW ************************************************************************************* IC-1 Interface Cable $12 LONG Interface Cable (120") for ICOM Radios listed Below Includes AC-1 cable IC-2 Interface Cable $8 SHORT Interface Cable (14") for ICOM Radios listed Below Y-ACC Cable $12 Cable for Interfacing LDG Autotuners with FT-857 and FT-897 Push-to-Tune Cable $12 Carrier Output from FT-857(D)/897(D) at the Push of a Button Aux. Power Cable SOLD OUT $12 Provides Power from FT-857(D)/897(D) for LDG Products Discontinued Product In-Line Fuse Cable - single $1.99 In-Line Fuse Cable - set of 3 $5 Allows Easy Inclusion of a Fuse in the Power Line of Your Equipment LDG Power Cable $5 FT-817 Power Cable $6.50 DIN-8 CAT Cable $12 AT-897 Replacement DIN-8 CAT Cable (male-to-male) DIN-8 Mating Pigtail Cables $8.50 DIN-8 Mating Pigtail Cables (1 each male and female) IC-7K Cable $8.0 Replacement Cable for AT-7000 ************************************************************************************* The IC-1 and IC-2 interface cables provide DC power and control between the radio and the autotuner. Supported Radios: IC-7000, IC-706, IC-707, IC-718, IC-725, IC-728, IC-736, IC-738, IC-746, IC-756, IC-765, and IC-775 (this interface will work with any ICOM radio that supports the ICOM AH-3 or AH-4 Tuner). Functionality: Pressing the tune button quickly on the radio by-passes the tuner. Pressing and holding the tune button on the radio or tuner starts the tune process. ************************************************************************************* The Y-ACC Cable is a low-cost alternative to the One Touch Tune for the FT-857(D) and FT-897(D) radios when interfacing with almost any LDG Autotuner. One end plugs into the radio and the other end into the autotuner. To operate, you simply press the tune button on the autotuner and the radio transmits a carrier while the autotuner proforms its tuning operation. When the autotuner has completed its task, the radio carrier is turned off and it returns to its prior operating mode. ************************************************************************************* The Push-to-Tune Cable is a low-cost means to cause the FT-857(D) and FT-897(D) radios to produce a carrier that is often used when adjusting an antenna tuner. One end plugs into the radio and the other end has a push button. To operate, you simply press the button and the radio transmits a carrier as long as the button is depressed. ************************************************************************************* The Auxillary Power Cable connects to the FT-857 and FT-897 CAT/LIN jack to provide power for LDG products. The plug is compatable with the LDG jacks. Discontinued Product ************************************************************************************* The In-Line Fuse Cable connectors allow easy inclusion of a fuse in the power line of your equipment. Connectors mate with LDG products. Includes a 2 A fuse that you can easily swap out. Adds safety to your equipment. ************************************************************************************* The LDG Power Cable connects to the all of the LDG products. This cable is a replacement cable for the power cable take was included with the LDG product. ************************************************************************************* The FT-817 Power Cable connects to the external power jack of the FT-817. This cable is a replacement cable for the power cable take was included with the FT-817. NOTE: This cable is not fused. ************************************************************************************* The DIN-8 CAT Cable connects the FT-897 CAT port and the LDG AT-897 autotuner. This cable is included when you purchase a new LDG AT-897 autotune. This cable has a male plug on each end. ************************************************************************************* The DIN-8 Pigtails can be used for the DIYer to connect many devices. You get two mating pigtail cables, one having a plug and one having a jack. ************************************************************************************* The IC-7K is the cable that connects the ICOM IC-7000 and LDG AT-7000. This is the replacement cable should yours become lost or damaged.